# The Pico HID
!!! tip "A fast way to get PS/2 on PiKVM V2+"
If you need PS/2 keyboard & mouse on [PiKVM V2](v2.md), [V3](v3.md) and [V4 Plus](v4.md)
(but not V4 Mini or DIY based on Zero 2 W boards),
you can use a faster and easier way: [The Pico HID Bridge](pico_hid_bridge.md).
The Pico HID is a part of [DIY PiKVM V1](v1.md) platform that performs keyboard and mouse emulation.
It has excellent compatibility, and emulates USB by default, including two mouse modes: absolute and relative.
Full list of features:
| Feature | Enabled by default |
|---------|--------------------|
| USB Keyboard, absolute & relative mouse | Yes |
| USB Absolute Mouse for Windows 95 | No |
| PS/2 Keyboard & mouse | No |
The scope of the Pico HID is not limited to [V1](v1.md) platform, it can also be used with [V2](v2.md) and [V3](v3.md),
if you need to emulate a PS/2 keyboard and mouse or use a [legacy multiport KVM switch](https://github.com/pikvm/pikvm/issues/7)
which does not fully support USB standards.
This page explains how to build, connect and use all the features of the Pico HID.
!!! note "Software requirements"
KVMD >= 3.241 is required for the Pico HID.
For new builds, this will be the case, but if you want to use the Pico HID on the old PiKVM, you will need to update OS.
-----
## Making the Pico HID
If you are building [PiKVM V1](v1.md), then the hardware should already be assembled. Skip this step unless you need PS/2 support.
But if you are making the Pico HID for [V2](v2.md) or [V3](v3.md), then follow this guide:
??? example "The Pico HID from scratch"
Parts list:
{!_pico_hid_parts.md!}
Connect all the parts according to this scheme:
??? example "Simple wiring diagram"
??? example "Electrical schematic diagram for advanced users"
### PS/2 Keyboard & Mouse
??? example "Additional steps for PS/2 support"
If you need PS/2 keyboard and mouse support, you will need a few additional components.
Soldering skills will also come in handy.
* *x1* 3.3V/5V bi-directional logic level shifter [like this](https://learn.sparkfun.com/tutorials/bi-directional-logic-level-converter-hookup-guide/).
* *x2* PS/2 cable with male connector (can be salvaged from the an keyboard or mouse).
Make sure that the level shifter pinout matches the scheme, and connect everything according to the [Pico pinout](https://pico.pinout.xyz).
```
_________________
| |
Pico GP11 ______| LV1 HV1 |______ PS/2 keyboard data
Pico GP12 ______| LV2 HV2 |______ PS/2 keyboard clock
Pico GP13 ______| LV HV |______ PS/2 5V
Pico GND ______| GND GND |______ PS/2 GND
Pico GP14 ______| LV3 HV3 |______ PS/2 mouse data
Pico GP15 ______| LV4 HV4 |______ PS/2 mouse clock
|_________________|
```
You can take the 5V power line from one of the PS/2, for example from the keyboard,
or from both at once, but use a multimeter to make sure that both PS/2 female
connectors have the same line.
PS/2 female socket pinout on the motherboard is the same for the keyboard and the mouse.
A purple socket usually corresponds to the keyboard, and a green one to the mouse.
If your motherboard only has one port, it's probably universal and can be used for both
the keyboard and the mouse. Most likely, it will be painted both colors.
Use a multimeter to determine the purpose of the wires in your PS/2 cables.
A good idea is to mount the level shifter on top of the Pico, as in this photo:
!!! note
Don't forget to enable PS/2 mode support as described in the next paragraph
-----
## Configuring the HID modes
By default, Pico HID emulates a USB keyboard and an absolute or relative mouse
(read [here](mouse.md) about the difference between mouse modes).
For most cases, nothing needs to be changed here. However, if you need something special
(like Windows 98 support), you can do it without reflashing the current firmware.
To achieve this, the Pico HID uses a runtime configuration, which is set by connecting
some GPIOs with Ground (`GND`) lines.
| Pin name on the Pico board | Description |
|----------|-------------|
| `GP2` | Enable PS/2 keyboard & mouse support (see below). |
| `GP3` | Prefer the PS/2 keyboard over USB when turning on the HID (if PS/2 is enabled). |
| `GP4` | Prefer the PS/2 mouse over USB (if PS/2 is enabled) |
| `GP6` | Disable USB keyboard & mouse support. This is useful if you only want to use PS/2. |
| `GP7` | Enable the special USB absolute mouse for Windows 98. |
| `GP8` | Prefer the relative USB mouse over the absolute one. |
| `GP9` | Prefer the Windows 98 USB absolute mouse over the regular absolute one (if enabled). |
!!! example
To enable Windows 98 absolute mouse, just connect pin `GP9` to any `GND` [on the Pico](https://pico.pinout.xyz).
-----
## Flashing the firmware
{!_pico_hid_flashing.md!}
-----
## The final steps
Connect the Pico HID to the target host using the USB cable.
If you are building PiKVM [V1](v1.md), no further action with the Pico HID is required.
If you are making the Pico HID for [V2](v2.md) or [V3](v3.md), add the following lines to the PiKVM configuration and reboot it:
* `/boot/config.txt`
```ini
dtoverlay=spi0-1cs
```
* `/etc/kvmd/override.yaml`:
```yaml
kvmd:
hid:
type: spi
chip: 0
bus: 0
sw_cs_pin: 7
sw_cs_per_byte: true
reset_pin: 25
reset_inverted: true
reset_self: true
power_detect_pin: 16
power_detect_pull_down: true
```
-----
## Replacing the Arduino HID
!!! warning
**This section is intended for advanced users of the [legacy Arduino HID](arduino_hid.md).**
It may seem tempting, but **don't to use the Arduino HID for new PiKVM builds**
just because you have it at your fingertips. Connecting and flashing Arduino
is much more time consuming than Pico. In addition, different Arduino board work
with different voltages, they may or may not have SPI (for the Pico, we use SPI to
free up the UART on Raspberry Pi for the console and other useful things), etc.
Using the Pico HID is the recommended fast and standard way in the PiKVM world.
The Pico HID can be used to replace the [legacy Arduino HID](arduino_hid.md).
It can use both Serial (UART) port and the SPI. The connection scheme is also much simpler,
getting rid of the transistor for the Reset line and the level shifter for RX/TX (MOSI/MISO).
??? example "For the Arduino HID over SPI"
Throw away the Reset transistor and level shifter, and follow this guide
from the very beginning, as if you were connecting Pico HID to PiKVM [V2](v2.md) or [V3](v3.md).
??? example "For the classic Serial (UART) HID"
Get rid of the transistor and level shifter, and follow this guide
from the very beginning, but the schemes and configs will be slightly different.
* The `GP22` on the Pico is connected directly to the `GND`. This enables UART mode instead of the default SPI.
* In the good old PiKVM V0, `GPIO4` [on the Raspberry Pi](https://pinout.xyz) was used for the Reset line.
Now we recommend to use `GPIO25` for consistency reasons.
However, you can use `GPIO4` by changing the `reset_pin` value in the config example below.
On the scheme, this is a yellow wire, the `RUN (Pico) -> GPIO25 (Pi)` line.
??? example "Simple wiring diagram"
??? example "Electrical schematic diagram"
??? example "Configs"
* Don't add line `dtoverlay=spi0-1cs` to the `/boot/config.txt` file. It's only needed for SPI.
* `/etc/kvmd/override.yaml`:
```yaml
kvmd:
hid:
type: serial
device: /dev/kvmd-hid
reset_pin: 25
reset_inverted: true
reset_self: true
power_detect_pin: 16
power_detect_pull_down: true
```