You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
103 lines
3.1 KiB
C
103 lines
3.1 KiB
C
// FARM DATA RELAY SYSTEM
|
|
//
|
|
// GATEWAY 2.000 Configuration
|
|
|
|
#include <fdrs_globals.h>
|
|
|
|
#define FDRS_DEBUG //Enable USB-Serial debugging
|
|
#define DEBUG_CONFIG // Displays full config info on startup
|
|
|
|
#define UNIT_MAC 0x02 // The address of this gateway
|
|
|
|
// Actions -- Define what happens when a packet arrives at each interface:
|
|
// Current function options are: sendESPNOW(MAC), sendSerial(), sendMQTT(),
|
|
// bufferLoRa(interface), bufferESPNOW(interface), bufferSerial(), and bufferMQTT().
|
|
|
|
#define ESPNOWG_ACT sendESPNOW(0x01);
|
|
#define SERIAL_ACT
|
|
#define MQTT_ACT
|
|
#define LORAG_ACT
|
|
|
|
// Protocols -- Define which protocols the gateway will use.
|
|
// Warning: ESP-NOW and WiFi should not be used simultaneously.
|
|
|
|
#define USE_ESPNOW
|
|
//#define USE_LORA
|
|
//#define USE_WIFI //Used only for MQTT gateway
|
|
|
|
// Neighbor addresses
|
|
#define ESPNOW_NEIGHBOR_1 0x01 // ESPNOW1 Address
|
|
#define ESPNOW_NEIGHBOR_2 0x0F // ESPNOW2 Address
|
|
#define LORA_NEIGHBOR_1 0x0E // LoRa1 Address
|
|
#define LORA_NEIGHBOR_2 0x0F // LoRa2 Address
|
|
|
|
// Neighbor Actions
|
|
#define ESPNOW1_ACT sendSerial(); // This would display packets arriving *from* the front-end.
|
|
#define ESPNOW2_ACT
|
|
#define LORA1_ACT
|
|
#define LORA2_ACT
|
|
|
|
//Pins for UART data interface (ESP32 only)
|
|
#define RXD2 14
|
|
#define TXD2 15
|
|
|
|
//Logging settings -- Logging will occur when MQTT is disconnected
|
|
//#define USE_SD_LOG //Enable SD-card logging
|
|
//#define USE_FS_LOG //Enable filesystem (flash) logging
|
|
#define LOGBUF_DELAY 10000 // Log Buffer Delay - in milliseconds
|
|
#define SD_SS 0 //SD card CS pin (Use different pins for LoRa and SD)
|
|
#define SD_FILENAME "fdrs_log.csv"
|
|
#define FS_FILENAME "fdrs_log.csv"
|
|
|
|
// SPI Configuration -- Needed only on Boards with multiple SPI interfaces like the ESP32
|
|
|
|
#define SPI_SCK 5
|
|
#define SPI_MISO 19
|
|
#define SPI_MOSI 27
|
|
|
|
// LoRa Configuration -- Needed only if using LoRa
|
|
#define LORA_SS 18
|
|
#define LORA_RST 14
|
|
#define LORA_DIO0 26
|
|
|
|
//433E6 for Asia
|
|
//866E6 for Europe
|
|
//915E6 for North America
|
|
#define LORA_BAND 915E6 // LoRa Frequency Band
|
|
#define LORA_SF 7 // LoRa Spreading Factor
|
|
#define LORA_TXPWR 17 // LoRa TX power in dBm (+2dBm - +20dBm), default is +17dBm.
|
|
|
|
// Buffer Delays - in milliseconds - Uncomment to enable any buffer
|
|
|
|
//#define ESPNOW1_DELAY 0
|
|
//#define ESPNOW2_DELAY 0
|
|
//#define ESPNOWG_DELAY 0
|
|
//#define SERIAL_DELAY 0
|
|
//#define MQTT_DELAY 0
|
|
//#define LORAG_DELAY 1000
|
|
//#define LORA1_DELAY 1000
|
|
//#define LORA2_DELAY 1000
|
|
|
|
#define PEER_TIMEOUT 300000
|
|
|
|
|
|
// FastLED -- Not yet fully implemented
|
|
//#define USE_LED
|
|
#define LED_PIN 32
|
|
#define NUM_LEDS 4
|
|
|
|
// WiFi and MQTT Credentials -- Needed for MQTT only if "fdrs_globals.h" is not included
|
|
//#define WIFI_SSID "Your SSID"
|
|
//#define WIFI_PASS "Your Password"
|
|
//#define MQTT_ADDR "192.168.0.8"
|
|
//#define MQTT_PORT 1883 // Default MQTT port is 1883
|
|
|
|
//#define MQTT_AUTH //Enable MQTT authentication
|
|
//#define MQTT_USER "Your MQTT Username"
|
|
//#define MQTT_PASS "Your MQTT Password"
|
|
|
|
// MQTT Topics
|
|
#define TOPIC_DATA "fdrs/data"
|
|
#define TOPIC_STATUS "fdrs/status"
|
|
#define TOPIC_COMMAND "fdrs/command"
|